How Long Does Fire Retardant Paint Last? A Complete Guide to Maintenance, Touch-Ups, Retreatment and Licence Renewal After Completion (with 30 FAQs)
Once fire retardant treatment is complete and the FS251 is in hand, many owners assume the job is done. In fact, like ordinary paint, fire retardant paint is affected by everyday use, cleaning, damp, wear and later renovation. After several years of operation, is the original treatment still effective? What should you watch out for when repainting, touching up or replacing materials? What do you need to prepare for licence renewal or a Fire Services Department (FSD) inspection? This guide sets out the key points for managing fire retardant treatment after completion, and finishes with 30 frequently asked questions.
Quick answer: There is no single "expiry date" that applies to every fire retardant paint. Used normally in the dry interior environment it was intended for, without wear or alteration, fire retardant treatment can generally last a long time. But if the material gets damp, is washed often, becomes worn or peels, is sanded or repainted, or is added to or altered, the original treatment may no longer be effective. It must then be reassessed and retreated, and a new FS251 obtained. Actual durability depends on the product used, the workmanship and the environment, so always follow the product information and the assessment of a registered contractor.
Contents
- Durability of fire retardant treatment
- How the environment affects performance
- Routine maintenance checklist
- Ten situations that call for retreatment
- The right way to touch up and repaint
- Managing curtain and fabric washing
- FS251, licence renewal and fitting-out alterations
- Document management
- 30 frequently asked questions
1. Durability of Fire Retardant Treatment
Fire retardant treatment works through a coating on the material surface or flame retardant ingredients that have penetrated the material. As long as these are not damaged, leached out or covered over, performance can be maintained. The main factors affecting durability are:
| Factor | Effect |
|---|---|
| Product type | Formulations and durability vary between products; some are only suitable for dry interiors |
| Workmanship | Insufficient coverage, too few coats or incomplete drying shorten effective life |
| Humidity | Flame retardant ingredients may absorb moisture or be leached out by water |
| Cleaning method | Frequent wiping with water or detergents may remove surface flame retardants |
| Wear | Coatings are more easily damaged in areas that are often touched or knocked |
| Sunlight | Prolonged sun exposure may age some coatings |
| Later alterations | Sanding, repainting, drilling and additions can all damage the original treatment |
Durability Classes for Reference
Requirements for Hong Kong licensed premises focus mainly on surface spread of flame classes and do not set separate durability classes. However, the European standard EN 16755 sets durability classes for fire-retardant-treated wood products, which can be used as a reference for judging which environment a product suits:
| Class | Intended environment | Examples |
|---|---|---|
| INT1 | Dry interior | General interior walls and ceilings |
| INT2 | Humid interior | Kitchens, changing rooms, pool halls, surfaces cleaned often |
| EXT | Exterior or semi-exposed | Outdoor timber structures, balconies |
Under that standard, the classification of INT1 and INT2 products remains valid for the service life of the wood product, provided they are used only in the intended environment. EXT products generally need maintenance or recoating by the method and at the intervals specified by the manufacturer. In other words, durability depends on "using the right product in the right place". If a product suited only to dry conditions is used where surfaces are wiped often, its performance may decline sooner.
2. How the Environment Affects Performance
Dry Interior Environments
Walls and ceilings in ordinary shops, offices and classrooms are relatively ideal environments. As long as there is no wear or alteration, fire retardant treatment can usually last a long time.
Humid and Frequently Cleaned Environments
Some areas of restaurants, clubhouses and fitness centres have higher humidity or need frequent cleaning. Even though they are indoors, they should be treated as humid environments. In these areas:
- Confirm before application that the product suits humid environments
- Avoid wiping treated surfaces with lots of water or strong detergents
- Check regularly for blistering, discolouration, peeling or mould
Areas That Are Often Touched or Knocked
Booth partitions, areas around door frames, cashier counters and corridor walls are easily knocked by bags, chairs and trolleys, so their coatings are more easily damaged. Include them in regular checks.
Ceilings and High-Level Areas
Ceilings are touched less and suffer less wear, but may be affected by air-conditioning drips, leaks or heat. If you find water stains, check the affected area. Also note that no decoration or false ceiling may obstruct the operation of sprinkler heads.
3. Routine Maintenance Checklist
A simple visual check every three to six months is recommended, together with a look during each annual fire service installation inspection:
| Item to check | What to look for |
|---|---|
| Coating appearance | Peeling, flaking, cracking, blistering |
| Surface damage | Scratches, dents from impact, exposed bare timber |
| Water stains and damp | Water marks, discolouration, mould, swollen timber |
| Signs of alteration | New holes, newly fitted items, partial replacements |
| Fabric condition | Number of washes, fading, damage, replacement |
| Sprinkler heads and fire service installations | Whether they are obstructed by decorations |
| Documents | Whether test reports and the FS251 are complete and match the site |
Cleaning Advice
- Wipe gently with a dry or slightly damp cloth, avoiding lots of water
- Avoid strong acid, strong alkaline or solvent-based cleaners
- Avoid scrubbing with sandpaper, wire brushes or hard bristle brushes
- For deep cleaning, check the method with the contractor or product supplier first
4. Ten Situations That Call for Retreatment
- Clear peeling or wear of the coating: where bare timber is exposed or the coating has thinned, performance can no longer be assured.
- The material has been badly damp or flooded: flame retardant ingredients may have been leached out.
- The surface has been sanded: sanding removes the surface coating.
- Repainting or recolouring: a new coating may cover or affect the original fire retardant layer; see the next section.
- Additions or replacement materials: new materials are untreated and not covered by the original FS251.
- Fabrics washed many times: treated flame retardant fabrics may lose effectiveness after repeated washing.
- Fabrics replaced or altered: new curtains and drapes need their own proof.
- Extensive drilling, cutting or modification: cut faces and drilled areas are untreated.
- Product used in the wrong environment: a product suited only to dry conditions used in a humid area.
- Required by the FSD or licensing authority: non-compliance identified at inspection.
Retreatment follows the same process as the first treatment. It must be carried out by a Class 2 Registered Fire Service Installation Contractor, who issues a new FS251 on completion. For the process, see The Fire Retardant Paint Process Explained: 12 Steps to FS251.
5. The Right Way to Touch Up and Repaint
Local Touch-Ups
Small areas of damage can be considered for local repair, but note the following:
- Touch-ups should use the same or a compatible fire retardant product as the original treatment, and be carried out by a registered contractor
- The area to be repaired must be clean and dry, with loose coating removed
- Coverage and number of coats must meet the product requirements
- After repair, confirm that the documents cover the repaired area
"Touching up the colour" with ordinary paint only hides the damage; it does not restore fire performance.
Full Repainting
When premises are refurbished, the most common problem is painting ordinary paint directly over treated materials. This can cause two problems:
- Ordinary paint is a combustible coating and changes how the material surface behaves in a fire.
- The new coating may prevent the fire retardant layer from expanding properly when heated.
Before repainting, confirm the following with the contractor:
- Whether the original fire retardant product allows a topcoat, and what type of topcoat can be used
- Any limits on topcoat type and thickness
- Whether retreatment and an updated FS251 will be needed after repainting
If this cannot be confirmed, the safer approach is to carry out fire retardant treatment again after repainting, or switch to materials that already have test reports.
Replacing Materials
When replacing individual timber boards, finishes or partitions, the new materials need their own proof: either choose materials with test reports, or arrange treatment before installation and painting. For whether different materials can be treated, see Which Materials Can Be Fire Retardant Treated?.
6. Managing Curtain and Fabric Washing
Fabrics are the fire-safe materials that need the most ongoing management, because washing is a necessary everyday task.
| Fabric type | Effect of washing | How to manage |
|---|---|---|
| Inherently flame retardant fabric | Flame retardancy comes from the fibre itself and is generally unaffected by washing | Wash according to the fabric supplier's guidance and keep the test report |
| Fabric treated with fire retardant solution | May lose effectiveness after repeated washing | Record the number of washes and assess after washing whether retreatment is needed |
Fabric Management Tips
- Keep a curtain washing log recording dates and washing methods
- Confirm the permitted washing methods and number of washes with the fabric supplier
- For fabrics treated with fire retardant solution, have the contractor assess them after washing
- For areas that need frequent washing, consider switching in the long term to inherently flame retardant fabric with a BS 5867-2 Type B report
- When replacing curtains, obtain test reports for the new fabric or arrange treatment at the same time
7. FS251, Licence Renewal and Fitting-Out Alterations
Does the FS251 Have an "Expiry Date"?
The FS251 reflects the result of a particular piece of work, certifying that a given fire retardant treatment was completed by a registered contractor. For fire service installations (such as fire alarm systems, sprinkler systems and fire extinguishers), the law requires owners to have them inspected by a registered contractor at least once every 12 months, which is why the industry often says "the annual inspection certificate is valid for one year". Fire retardant treatment is a different type of work, and its certificate is not renewed annually as such. However, once materials in the premises are altered, the original certificate no longer covers the altered situation.
Updated FS251 Forms
The FSD has introduced the FS251 (Revision 1/2025). The old FS251 (Revision 1/2016) was abolished from 1 April 2026, and from 1 July 2026 certificates must be prepared, signed and submitted electronically. Old certificates still reflect work completed in the past, but any new treatment will be certified on the new version.
Acceptable Material Standards
The FSD's licensed premises fire safety information website states that combustible materials used for false ceilings, partitions or wall finishes must meet BS 476 Part 7 Class 1 or Class 2, EN 13501-1 Class C or above, or another standard accepted by the Director of Fire Services, or be treated with fire retardant paint or solution by a Registered Fire Service Installation Contractor. When replacing materials in future, check the test reports for new materials against these standards. For an explanation of the standards, see BS 476 Part 7 Class 1 vs Class 2.
Alterations While Licensed
If a licensee uses combustible materials or makes alterations involving them during the licence period, the licensee must confirm that the materials meet flammability standards and keep test reports or an FS251, whichever applies. Failure to comply may be treated as a breach of licensing conditions. For restaurant requirements, see Fire Retardant Paint and False Ceiling Requirements for Restaurants.
Pre-Renewal Checks
| Item to check | Confirmed |
|---|---|
| Whether any combustible materials have been added, replaced or altered since the last treatment | □ |
| Whether any repainting, sanding or major repairs have been carried out | □ |
| Whether curtains and drapes have been replaced or washed many times | □ |
| Whether materials on site match the FS251 and test reports | □ |
| Whether the annual fire service installation inspection has been completed | □ |
| Whether sprinkler heads and other fire service installations are obstructed by decorations | □ |
For annual fire service installation inspections, see our Complete Guide to Fire System Maintenance and FS251 Annual Inspection.
8. Document Management
Good document management saves a great deal of time at FSD inspections, licence renewals, changes of ownership and insurance claims. Set up a "fire-safe materials file" containing:
- A material list showing location, type and area
- Test reports for each material
- All FS251 electronic certificates
- Information on the fire retardant products used
- Before and after photos
- Records of every alteration, repair and retreatment
- Curtain washing and replacement records
- Quotations and invoices
Back up the documents electronically and update them immediately after each alteration. When the premises changes hands or tenants, hand over the file as well.
9. 30 Frequently Asked Questions
Service Life and Durability
1. How long does fire retardant paint last?
There is no single service life that applies to every product. Used normally in the dry interior environment it was intended for, without wear or alteration, fire retardant treatment can generally last a long time. Actual durability depends on the product, workmanship and environment.
2. Does fire retardant paint wear off on its own?
In a suitable environment, fire retardant treatment generally does not stop working for no reason. Damp, washing, wear, sunlight, sanding or repainting can all reduce performance.
3. Does fire retardant paint need redoing every year?
Generally not. But if materials are altered or damaged, or the environment changes, it must be reassessed. Fire service installations, by contrast, must be inspected at least once every 12 months; the two are different.
4. Does fire retardant paint fail faster in damp environments?
It may. Flame retardant ingredients may absorb moisture or be leached out by water. Kitchens and frequently cleaned areas should use products suited to humid environments and be checked regularly.
5. Can interior fire retardant paint be used on outdoor timber?
It is not recommended. Outdoor environments are affected by rain, sunlight and temperature changes, so a product suitable for exterior use must be chosen, and it generally needs maintenance by the method and at the intervals specified by the manufacturer.
6. How can I tell whether fire retardant treatment is still effective?
It is hard to confirm by eye alone. Start by checking for peeling, wear, damp or alterations; if in doubt, have a registered contractor assess it.
Maintenance and Cleaning
7. Can treated timber walls be wiped with water?
Yes, with a dry or slightly damp cloth, but avoid lots of water and strong detergents, which could remove surface flame retardants.
8. Can detergents be used to clean fire retardant paint surfaces?
Avoid strong acid, strong alkaline or solvent-based cleaners. For deep cleaning, check the method with the contractor or product supplier first.
9. How often should fire retardant treatment be checked?
A simple visual check every three to six months is recommended, together with a look during each annual fire service installation inspection, before licence renewal and before any renovation.
10. What should I do if mould appears on a fire retardant paint surface?
Mould shows that the area has been damp for a long time, and flame retardant performance may have been affected. Deal with the source of damp first, then have a contractor assess whether retreatment is needed.
11. Air-conditioning drips have wet the ceiling. Does it need attention?
Fix the drip first, then check the affected area. If the material has been badly damp, deformed or discoloured, arrange an assessment.
Touch-Ups and Repainting
12. Can I touch up scratched fire retardant paint myself?
Touching up the colour with ordinary paint only hides the damage and does not restore fire performance. Repairs in licensed premises should be carried out by a registered contractor using a compatible fire retardant product.
13. Can ordinary paint be applied over fire retardant paint?
First confirm whether the original product allows a topcoat and what type can be used. Ordinary paint may change how the surface behaves in a fire and may prevent the fire retardant layer from expanding.
14. Is fire retardant treatment needed again after repainting?
It depends on the topcoat and the original product's requirements. If you cannot confirm that the topcoat is compatible with the fire retardant product, the safer approach is to retreat after repainting and obtain a new FS251.
15. Does timber still have fire protection after sanding?
Sanding removes the surface coating, so the original fire protection has generally been affected and retreatment is needed.
16. Does drilling into treated boards need attention?
A few small holes generally have limited effect. Extensive drilling, cutting or modification leaves untreated cut faces, which should be assessed by a contractor.
17. If I replace some boards, does the whole wall need retreating?
Generally only the newly replaced materials need treating, but confirm that documents for both old and new materials are complete and match the site.
Fabrics and Curtains
18. How many times can curtains sprayed with fire retardant solution be washed?
It depends on the fabric and product, so confirm with the supplier. Treated flame retardant fabrics may lose effectiveness after repeated washing, so assess after washing whether retreatment is needed.
19. Can curtains be dry-cleaned?
It depends on the fabric and fire retardant product; some treatments may be affected by dry-cleaning solvents. Check before cleaning.
20. Do inherently flame retardant curtains need retreating?
The flame retardancy of inherently flame retardant fabric comes from the fibre itself and is generally unaffected by washing, so no retreatment is needed. Wash according to the supplier's guidance and keep the test report.
21. What documents are needed for new curtains?
New curtains need a test report showing they meet BS 5867-2 Type B, or must be treated with an accepted fire retardant solution by a Class 2 registered contractor who issues an FS251.
FS251 and Documents
22. Does the FS251 for fire retardant paint expire?
The FS251 reflects the result of a particular piece of work, and certificates for fire retardant treatment are not renewed annually as such. However, once materials in the premises are altered, the original certificate no longer covers the altered situation.
23. Are old-version FS251 certificates still valid?
Old certificates still reflect work completed in the past. The old FS251 (Revision 1/2016) form was abolished from 1 April 2026, and any new treatment must be certified on the new version and submitted electronically.
24. What if I lose the FS251?
Contact the original contractor for a copy. Back up electronic certificates straight away to avoid losing them.
25. Can the original FS251 still be used after the premises changes hands?
If the materials have not been altered, the original certificate still reflects their treatment, but the new operator should verify that the documents match the site. If the new operator alters the fitting-out, it must be dealt with according to the new situation.
26. Besides BS 476, which other standards are acceptable?
The FSD's licensed premises fire safety information website states that EN 13501-1 Class C or above, or another standard accepted by the Director of Fire Services, is also acceptable. When replacing materials, check test reports against these standards.
Licence Renewal and Alterations
27. Is fire retardant paint needed again at licence renewal?
If the materials have not been altered or damaged, retreatment is generally not needed, but confirm that the documents are complete and match the site. If there have been alterations, deal with them according to the new situation.
28. Who needs to be notified when adding partitions during the licence period?
The licensee must confirm that the new materials meet flammability standards and submit test reports or an FS251 as required. The specific procedure follows the requirements of the licensing authority and the FSD.
29. Can added decorations affect fire service installations?
Yes. No decoration, false ceiling or structure may obstruct the operation of sprinkler heads or other fire service installations. Confirm locations before adding anything.
30. How can I reduce the need for retreatment in future?
Choose products suited to the environment, use more durable materials in damp or frequently cleaned areas, choose inherently flame retardant fabric for curtains, avoid repainting over treated materials without checking, and keep complete records of documents and alterations.
Fire Retardant Treatment Assessment and Retreatment
Grand United Eng., Co. is a Registered Fire Service Installation Contractor in Hong Kong. For premises already in operation, we can assess the condition of existing fire retardant treatment, check documents before refurbishment, alterations or licence renewal, and arrange retreatment and a new FS251. When you contact us, please provide the premises use, the date of the last treatment, existing certificates, details of any alterations and site photos. You can also read What Is Fire Retardant Paint? and How Much Does Fire Retardant Paint Cost?, and browse our Project Cases.
Book a fire retardant treatment assessment, or call 2667 7701.
